..!! CruiserSuite TP Full Unlocker v1.00 released !!..

| 0 comments

Dear all,

we have just released most wanted SonyEricsson Full Unlocker via TestPoint with Security Zone repair possibility. The CruiserSuite TP Full Unlocker requires UC-20 TestPoint cable - you can buy it from any of our resellers.

All other TestPoint solutions force the phone address bus pins to 3.3V which is exceeding its maximal allowed voltage almost twice. Only the UC-20 TP cable was designed to prevent this and avoid likely flash chip damage.

Here are release notes of CruiserSuite TP Full Unlocker v1.00:

  • Simple to use & failsafe
  • Supports all DB2020 plattform based SonyEricsson phones
  • All current CIDs are suported
  • This software is for all users who can disassemble the phone - also for inexperienced ones. (For disassembling phones, we recommend to read proper SonyEricsson service manuals.)
  • TP Full Unlocker does not destroy phone calibration data (so typical for SeTool ... )
  • For the phone safety, TestPointing requires UC-20 TP cable.
  • Unlike other amateur solutions which use external battery connection to the TP, our software uses specially designed UC-20 cable which can handle different bus voltages and prevents any potential flash chip damage.
  • TP is done in two stages. Once you complete TP stage 1 you don't need to repeat it anymore. Phone is then bootable via the 2nd testpoint anytime.
  • PDF manual is available after installation as usual in Documents folder

You can download the software from our Downloads section or from this Rapidshare link.



ENJOY!

F.A.Q About P2K Series.

| 0 comments

Here Is Little Info About P2K ..

May Be This Can Help All Users..

1 P2k How To Connect Phone With Pc.?
A. Use P2k Driver To Detect Phone At Modem .Like Here Software Is Auto install So Just Tick On "Clean And Reinstall " Press Start It Install All. Here Is Link For P2k Driver Only Without Auto Install.
B. After Installing Modem You Have To Switch Phone To P2k Mode To Accept All Another Drivers Which Need For Read And Repair .Use Rsd Lite To Do That.. Link Is Here

2 What Is Rezone We Have To Install Driver?
A. Motorola All Command And Loader Base On Factory Info.So They Using P2k Mode And Flash Mode To Access, Modification And Any Changing If We Need.
B. Without Driver We Can't See Phone So Must Install Before Do Anything.. And Open Rsd Lite To Let Him Complete Installation.

3 What Is Rezone We Need Rsd Lite?
A. There Is Many Rezone .[1] To Install Complete Driver.[2] To Flash Firmware To Phone [3] Flash Fex File To Phone.

4 What Is Flash Mode?
A. Flash Mode Is Most Important Thing We Need To Flash Phone And Repair Phone. By Pressing {*+#+Power Button} You See Black Screen Which Come Because Of Flash Mode. With Much Info That What In Phone..

5 What Is P2k Mode?
A. P2k Mode Is Need To Send Phone Commands Receiving Data..
B. Modified Flex Area.
C. Modified User Area Like User Code Security Code.

6 At Flash Mode In Phone I Can See Many Info. What Are They?
A. Most Important Info. Boot loader Xx ***x
B. Software Version Info.
C. Interface Which Is Connected.

7 What Is Boot Loader?
A. Boot loader Is = Flash Mode.. Without Boot Loader Your Phone Go To Special Blank Mode.

8 What Is Software Version?
A. Software Version Which Ur Phone Have. You Must Flash Same Version Or Newer Then It Firmware Or Monster Flash File To Phone Only..

9 What Is Blank Mode?
A. Blank Mode Is Special Mode To Use Unlocking Changing Pds And If We Losted Boot loader Then Its Come..

10 How To We Know That Phone Is In Blank Mode?
A. Just Plug Cable To Phone And Pc Your Phone Detect As S Blank ****** Means Your Phone Have No Valid Boot loader. So Its In Blank. You Can Call Him Dead Phone Right Now..

11 What Is Lte And Lte2 Prog And Aragon?
A. Its Are Cpu That Phone Use.

12 What Is Pds?
A. Pds Contact So Much Info About Phone Security .
B. Pds Have Lock Data
C. Pds Have Calculated Security Of Phone.
D. Pds Can Be Rewrites Or Recalculated Via Only Tp. Or Blank Mode With Special Method.

13 What Is Rezone At Phone Flash Mode We See Code Corrupted?
A. Firmware Damaged So First Reflash It
B. Pds And Firmware Code Not Matched Do Pds Repair And Reflash It.

14 What Is Rezone We See Mem Blank At Phone Flash Mode?
A. Firmware Area Damaged Reflash Will Fix It.
B. Boot Area Damaged Install Boot Will Fix It.
C. Pds Area Damaged Recalculate Or Rewrite Pds Then Flash Will Fix It.

15 What Is Rezone We See Some Time Lcd Problem?
A. Flex Area Have Special Part For Lcd Setting Rf Value You Need To Rewrite It.

16 How To Flash Phone With Rsd Lite?
A. Simple Just Connect Phone At Flash Mode [*+#+Power Button]
And Select Active Ur Model & Select Correct Flash File And Press Start ..

17 How To Check Software Version And Boot loader If Phone Lcd Damage Or Blank ?
A. Just Use Simple Flash Mode [*+#+Power Button] And Open Rsd Lite To See Phone Info. For More Details Just See Image.

18 Why Some Phone Start At Flash Mode Only?
A. Firmware Damaged Reflashing Full Flash May Solve
B. Pds Damaged Recalculate Or Rewrite Then Full Flash Need To Resolve Problem

19 What Is Image Flash? (RFDI)
A. It Is Repair File For Repair Boot And Pds For Blank Phones Only. If U Have Phone Which Is Detect In Blank Mode Only. Use RFDI Image To Restore/Repair Pds And Boot Area. After Flashing RFDI File You Must Flash Monster Flash Or Reflash To Phone.

20 What Is Monster Flash And Reflash?
A. Reflash Come With Only Firmware And Drm Area.
B. Monster Flash Come With Firmware, Flex, Pds Info, Drm, Lang, Mostly Everything.

21 What Is Rezone Software Not Found Phone Start At Flash Mode Only?
A. Phone Firmware Damaged Reflash Monster Flash Only. To Check
B. Pds Corrupted Rewrite Or Recalculate Then Full Flash May Solve It.
C. Still Same Just Problem With Version In Case You Must Erase Phone Flash Then Do Image Flash To Restore Boot are Then Pds Repair To Check You Get Firmware Version Or Not. If Yes Reflash Latest Version .If No Then Have Bad Hardware At Phone.

NEWEST AUTO INSTALL DRIVERHERE

IMODE DRIVER ONLY FOR IMODE BASE MOTOROLA
HERE
Just Wait For Unlocking Info Soon I Post Every Tested Phone Method To Unlock And Repair Free.


HOPE THIS CAN HELP ALL..

note : i will update this thread day by day..

BEST REGARDS
Gopal Chevli.

SmartMoto v3.15, Smart-Clip v4.08, S-Card 2.09 and Smart Adaptor v1.05

Dear users,
We are pleased to introduce a new version of SmartMoto v3.15, Smart-Clip v4.08, S-Card 2.09 and Smart Adaptor v1.05.

With this release we present the following options.

  1. Released Unlock, Format FFS and Repair EEPROM for the model W375В (Compal unlock procedure).
  2. The models W161 and W181 are added to the supported models list (although they were already supported before).
  3. Improved Prepare cycle for the models W510/W490. From now on, the handsets with an error 0085/00CA are supported.
  4. The model W270 was already supported for unlock, and now, Repair EEPROM and Format FFS are added for it.
  5. Developed Repair PDS function for the model U3.
  6. V365 fw R444HL1 is now included to the list of PDS Repair supported (although it was supported before).


Please don’t forget to update all your products and use Smart-Clip Update Zone to update S-Card.
Update Smart-Clip first and perform S-Card update after that only.
We recommend to use only the latest versions of Smart-Clip, S-Card, Smart Adaptor and SmartMoto.
If you wish to receive news on updates immediately, please subscribe to our new SMS notification system.


Smart-Clip ON!

A1 Java Unlocker FAQ

| 0 comments

What should you do if an error message in A1 Java Unlocker appears?

Error: File executor has not been found or you can’t find executor program in games (in manually run java program).

Start unlocking again and follow instructions carefully, especially when you’re asked to power on phone and wait for finish “Please wait” customization.


Error: At the end of procedure: Sending loader... Error: 0xA8A269DB

Before last attaching by ‘C‘ remove SIM card from phone.


Error: Flash Firmware version is not supported. Try another version.

This version of the firmware is not supported yet. We will prepare restore files for these firmware versions soon.


Error: Connecting via SEMC WMC Device (COM34, COM33). Error: 0xA8A269DB

  1. Do you have in phone SIM card which is accepted by phone? Can you enter menu on
    phone etc.?
    If you see “Insert Correct SIM Card” it means your SIM card is not accepted.
  2. Uninstall Sony Ericsson PC Suite or any other program which can use phone as
    modem device.


Error: While flashing the files: 0x5593BD55

Chosen flash files do not correspond with phone type or phone CID.

Clearing Phone Lock of DB2020, DB2012, PNX and old DBs

| 0 comments

Pressing Clear phone lock takes credit on DB2020 phones (unless CT fixed this on their next update)...

That's not the way to do if you want it free with Cruiser+...
for DB2020 you need to flash your phone:
(so far this is what i have tried, i have not try other way)

  1. attach
  2. flash main
  3. flash fs
  4. customize
  5. clear phone lock
  6. press turn-off phone

when power on phone it will still ask phone lock (just enter its default: 0000)


Reading only phone lock on DB2012, PNX, old DB***x, (via rj45)

  1. choose "identify" on boot options of primary folder
  2. press attach.


Reading phone lock of DB2020 PDA:

  1. there is a "pda info reader" on the support site, just download it.


Clearing phone lock of A2 phone:

  1. download "se a2 flasher" from support site
  2. then check "user code reset".


hope it is clear....
no more can't read phonelock, no credits, no need suggest to use other tools

author: kcgckc2002

How To Unlock a Sony Ericsson Phone by Cruiser !!!

| 0 comments

  • Remove and ReAttach Battery from phone
  • Start Cruiser
  • Click On USB
  • Click on "Attach Phone"
  • Click on "Security RSA"
  • Then "Unlock RSA"
  • Look on what Cruiser asks to do...
  • Then go on FLASH - Flash ARM - and Select SW File
  • Now Click on Write RAW FS and select fs file
  • Now go on "Locks" - Direct Unlock
  • Now return on "Flash" - Customize FS
  • Now click on Turn Off Phone
  • Unlock Done - Great Work BOSS :D !
author: dengel

Cruiser Plus 13.20 released

| 0 comments

Hi all,

we have just released new version of Cruiser+ v13.20. Here is the release info:

  • Cruiser software now supports Cruiser UC-20 cable. Updated built-in customizations. [also in Cruiser]
  • Updated TAC list for K320i, K530i, K770i, K800i, S500i, W200i, W380i, W580i, W610i, W660i. [also in Cruiser]
  • Fixed a minor bug related to W350 phones. [also in Cruiser]
  • Solved an issue with some DB2012 phones. [also in Cruiser]
  • Several internal software modules have been updated. [also in Cruiser]

Here is the Rapidshare link.

ENJOY

TUTORIAL cid49,51to52 CONVERT !!!

| 0 comments

Tutorial on converting DB2020 cid49/cid51 to cid 52 and unlock
Since that the unlocking of DB2020 cid52 is free, you can unlock cid49/cid51 without using or wasting log credits by converting it to cid52.
Note:
Use DCU-60 cable.
Procedure:
1. identify phone first by ticking "Identify" button.
Code:



v0.914014/UNI
Card serial:000xxxxx
Loaded 51 flash descriptors
Open COM port OK
ChipID:9900,EMP protocol:0301
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35463701962686 CERT:N/A
FLASH CID:51 COLOR:RED
Model:K610i
MAPP CXC article: R1GB001 prgCXC1250374_GENERIC_TH
MAPP CXC version: R1GB001
Language Package:T_MOB_INT_A
CDA article: CDA102497/8
CDA version: R12A
Default article: cxc1250376
Default version: R1GB001
Extended LOCKED
Operator: MULTIPLE
RESTORATION FILE PRESENT FOR DETECTED FIRMWARE
Elapsed:5 secs.



2.goto "settings" tab then tick "use server for csca flash/unlock and empty user/password section


3. write this misc. files "DB2020_CID49_51_to_CID52" then tick "write script"
* you can find this file in script folder
Code:



SERVER SUPPORT ENABLED.
ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:51
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35463701962686 CERT:RED
FLASH CID:51 COLOR:RED
PATCH:061205 1523 HANCXC9876543210_DB2020_MEM_PATCHER_R2A006 0
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
LDR:070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
loader filesystem startup: executed
loader unlock: executed
Will execute script now.
Writing GDFS var 0001:084E len:010B
Success
Phone detached
Elapsed:29 secs.



4. tick "identify" button again and the result is like this
Code:



SERVER SUPPORT ENABLED.
ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35463701962686 CERT:RED
FLASH CID:52 COLOR:RED
Model:K610i
MAPP CXC article: R1GB001 prgCXC1250374_GENERIC_TH
MAPP CXC version: R1GB001
Language Package:T_MOB_INT_A
CDA article: CDA102497/8
CDA version: R12A
Default article: cxc1250376
Default version: R1GB001
Extended LOCKED
Operator: MULTIPLE
RESTORATION FILE PRESENT FOR DETECTED FIRMWARE
SECURITY UNITS BACKUP CREATED.



Now your phone is cid52... The phone is ready to unlock..
Unlocking Procedure:

1. In "Settings" Tab tick "Complete phone after flash", "Unlock After Flash", "Use sever for csca unlock/flash", "Enable alternative security bypass" and empty user/password area.
2. Add flash files Main & fs (you need to put main & fs files if you don't have the same files that the phone is presently using, but if you have files then you can use the main file only.)
3. then click "Flash" button and follow all instructions and wait until it finished.
Code:

SERVER SUPPORT ENABLED.
ALTERNATIVE SECURITY BYPASS ENABLED.
ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35463701962686 CERT:RED
FLASH CID:52 COLOR:RED
PATCH:061205 1523 HANCXC9876543210_DB2020_MEM_PATCHER_R2A006 0
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CID52 BYPASS PROCEDURE STARTED
Processing part1...
Processing part2...
Processing part3....
OTP LOCKED:1 CID:51 PAF:1 IMEI:35463701962686 CERT:RED
FLASH CID:52 COLOR:RED
PATCH:061205 1523 HANCXC9876543210_DB2020_MEM_PATCHER_R2A006 0
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
REMOVE CABLE FROM PHONE
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
HOLD "C" BUTTON AND ATTACH AGAIN
CID52 BYPASS PROCEDURE FINISHED
ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
Trying to launch embedded bootloader...
Embedded flashloader:
DB2020_PRELOADER_FOR_SETOOL2
Flash ID check:897E
Flash props sent ok
writing D:\Downloads\setool3 flash files\k610\cid52\R1JG001_1250540_CHINA_TH.ssw
CURRENT FLASH FILE CID:52
SSW uses complete hash, hash len is:9200
Will flash 460 blocks...
SSW loading returns:0
writing D:\Downloads\setool3 flash files\k610\cid52\R1JG001_FS_APAC_TH_RED_CID52.ssw
CURRENT FLASH FILE CID:52
SSW uses complete hash, hash len is:2740
Will flash 137 blocks...
SSW loading returns:0
full sig complete.
USERCODE RESET TO "0000"
Searching...
Firmware lock check determined.
loader startup: executed
loader GDFS startup: executed
loader filesystem startup: executed
loader unlock: executed
writing tpa/preset/custom/C3_PCA_G3v2.cer
writing tpa/preset/custom/CONTENT_DOWNLOAD_HOOK_2.itm
writing tpa/preset/custom/customize.xml
writing tpa/preset/custom/DESKTOP_HOOK_2.itm
writing tpa/preset/custom/Entrust.net Root Certificate.cer
writing tpa/preset/custom/Entrust.net_WTLS_Root_Certificate.wcrt
writing tpa/preset/custom/FM_PICTURES_HOOK_3.itm
writing tpa/preset/custom/FM_SOUNDS_HOOK_3.itm
writing tpa/preset/custom/FM_THEMES_HOOK_3.itm
writing tpa/preset/custom/FM_VIDEOS_HOOK_3.itm
writing tpa/preset/custom/GAMES_HOOK_3.itm
writing tpa/preset/custom/GTE_CyberTrust_Root.cer
writing tpa/preset/custom/GTE_Cybe_Trust_Root_WTLS.wcrt
writing tpa/preset/custom/Root.cer
writing tpa/preset/custom/SEMC_E2E_Root_CA.crt
writing tpa/preset/custom/SETT_RINGTONE_HOOK_3.itm
writing tpa/preset/custom/ThawtePremium.der
writing tpa/preset/custom/ThawteServerCA.cer
writing tpa/preset/custom/Utiroot.cer
writing tpa/preset/custom/VeriSignClass3Root.cer
writing tpa/preset/custom/Verisign_Class_3_CA_WTLS.wcrt
Phone detached
Elapsed:989 secs.

You have now working unlocked DB2020 cid52 phones....
Happy unlocking.